Advances in flow analysis /

Advances in flow analysis /

Show other versions (1)

Bibliographic Details
Other Authors:	Trojanowicz, Marek
Format:	Book
Language:	English
Published:	Weinheim : Wiley-VCH, [2008]
Subjects:	Flow injection analysis. Flow Injection Analysis.

Similar Items

Flow injection analysis : instrumentation and applications /
by: Trojanowicz, Marek
Published: (2000)

Flow injection separation and preconcentration /
by: Fang, Zhaolun
Published: (1993)

Flow analysis with atomic spectrometric detectors /
Published: (1999)

Flow injection analysis (FIA) based on enzymes or antibodies /
Published: (1991)

Flow analysis with spectrophotometric and luminometric detection /
by: Worsfold, Paul
Published: (2012)

Flow injection analysis of marine samples /
by: Yebra-Biurrun, M. C.
Published: (2009)

Flow injection atomic absorption spectrometry /
by: Fang, Zhaolun
Published: (1995)

Advances in flow analysis /
Published: (2008)

The determination of pH by flow injection analysis and by fiber optrode analysis : project summary /
by: Pia, Stephen H.
Published: (1988)

Effect of jet injection angle and number of jets on mixing and emissions from a reacting crossflow at atmospheric pressure /
by: St. John, D.
Published: (2000)

A study of the effects of converging and diverging flow on the instability of viscous fingers /
by: Wylie, Joel Albert, 1963-
Published: (1987)

Flow analysis of injection molds /
by: Kennedy, Peter (Peter K.)
Published: (1995)

Injection molding advanced troubleshooting guide /
by: Kerkstra, Randy, et al.
Published: (2018)

Injection molding advanced troubleshooting guide : the 4M approach /
by: Kerkstra, Randy, et al.
Published: (2021)

Injection molding : technology and fundamentals /
Published: (2009)

Flow analysis of injection molds /
by: Kennedy, Peter (Peter K.)
Published: (2013)

Microbubble drag reduction phenomenon study in a channel flow /
by: Jimenez Bernal, Jose Alfredo, 1974-
Published: (2005)

Simulations of spray reacting flows in a single element LDI injector with and without invoking an Eulerian scalar PDF method /
by: Shih, Tsan-Hsing, 1940-
Published: (2012)

Development of advanced low emission injectors and high-bandwidth fuel flow modulation valves /
by: Mansour, Adel
Published: (2015)

Advanced injection molding technologies /
Published: (2019)

Assessment of hydrogeologic conditions with emphasis on water quality and wastewater injection, southwest Sarasota and West Charlotte Counties, Florida /
by: Hutchinson, C. B.
Published: (1992)

Gastrow injection molds : 130 proven designs.
by: Gastrow, Hans
Published: (2006)

Gastrow injection molds : 130 proven designs.
by: Gastrow, Hans
Published: (2006)

Plastics injection molding : scientific molding, recommendations, and best practices.
by: Lerma Valero, José R.
Published: (2020)

Mixing of an airblast-atomized fuel spray injected into a crossflow of air /
by: Leong, May Y.
Published: (2000)

Study of injection of helium into supersonic air flow using Rayleigh scattering /
by: Seasholtz, Richard G.

Study of injection of helium into supersonic air flow using Rayleigh scattering /
by: Seasholtz, Richard G., et al.
Published: (1997)

Selecting injection molds : weighing cost versus productivity /
by: Rees, Herbert, 1915-
Published: (2006)

Injection molding of metals and ceramics /
by: German, Randall M., 1946-
Published: (1997)

Prediction of pressurant mass requirements for axisymmetric liquid hydrogen tanks.
by: Van Dresar, N. T.
Published: (1995)

Semiconductor injection lasers /
Published: (1980)

Giving a subcutaneous injection /
by: Gay, Kathy
Published: (1989)

Numerical simulations of two-phase reacting flow in a single-element lean direct injection (LDI) combustor using NCC /
by: Liu, Nan-Suey
Published: (2011)

A simulation study of steam and steam-propane injection using a novel smart horizontal producer to enhance oil production /
by: Sandoval Muñoz, Jorge Eduardo
Published: (2004)

Simulation of hydraulic fractures and their interactions with natural fractures.
by: Sesetty, Varahanaresh
Published: (2012)

Micro injection molding /
by: Tosello, Guido
Published: (2018)

Injectable fillers : facial shaping and contouring /
Published: (2019)

Development of a Well Intervention Toolkit to Analyze Initial Wellbore Conditions and Evaluate Injection Pressures, Flow Path, Well Kill, and Plugging Procedures /
by: Paknejad, Amir Saman
Published: (2013)

The mould design guide /
by: Jones, Peter
Published: (2008)

Injection molding : an introduction /
by: Pötsch, Gerd
Published: (2008)